rinaprasant

hello thanks for reply but car limit 80 km/h , i open most of in car no any device install & here in india some people do with ecu thanks

hello i have bmw 520d g30 speed lock 80 km/h MDG1_MD1CS001 Bosch SW.: #DME__DDE802L#C5#BTL##CB_011_253.5_1.K/ #DME__DDE802L#C5#PST##38/1/MDG1_MD1CS001/11/P_1401//VLWT0//// #DME__DDE802L#C5#DST#B47D20O0-G30B47O0_2W5_AT below attach file if nay one have tune file or solutions if paid no problem thanks bmw_bosch_md1cs001_tc298tp_bench_fullbackup_35304d37303035371bc00025201802150b01ffffffaaaaaaffffffffffffffff_20221226121828_int_flash.rar

is it not possible if paid solution no problem thanks

hello i have suzuki patrol bosch me17.9.5 i need dtc remove = P0102 - mass or volume air flow "a" circuit low thanks fal_bosch_me17.9.51_bench_fullbackup_430007870b40100d82060010270af200_20220823120019.zip

stering collum not unlock ?

below attach which i have thanks eee.bin p-flash.bin

hello if any help below attach vergin data thanks jagur xf bcm vergin data.rar

if u have any programmer than read d-flash for bcm & send me i will repair data thanks

hello i have suzuki bosch ertiga patrol / cng 33920-72RS0 bosch 17.9.64 / tc1724n in india speed limit 80km but i have file with unlock file 220km but one customer need 98 or 100 km lock speed below i attach 80km speed lock & no speed limit file if any one help me or modified 98 or 100 km file thannks suzuki 17.9.64.rar

link not working thanks

hello for saftey i read epprom password with magic x17 so on table make jumper & write i have renault patrol same part no immo off file car satrt with 0 error remote not work thanks

hello its my mistake bcoz car nissan & i go with renault so that why key not accept thanks now i download nissan consult 3 with passthrough all ok but module not connect thanks

thanks i download & try with passthrough if i success , i will tell u thanks

thanks i have avdi but not full renault active can clip u have software & can work with pass through thanks

thanks for reply isk & pin read done , but after that car off & now not learn i think every time new pin & isk when i try to read any solution for orignal key recover or key need to unlock ? thanks

hello i have renault kicks patrol bcm t4 n3vs spc5605 problem with renolink i unable isk reading after that pin & isk calculated perfect but after start learn always fail thanks

renault captur 2018 job done 1] i find perfect renault duster patrol with orignal car 2] with magic x17 read via obd epprom password 3] with magic x17 make boot jumper & use epprom password & write flash immo data 4] this immo off ecu perfcet working in captur with no error 5] in duster i have new ecu with renolink parring with pin number bcoz duster easy to read with pin renolink so finally all job done thanks to all of u thanks

hello i have vovlo s60 d4 engine year 2017 module p31658440 / 028501339 T11710270312 EEPROM 95128 data may clear but in airbag module error / U210100 - CONTROL MODULE CONFIGURATION INCOMPATIBLE my vin - YV1FSA8CDJ2459988 below attach my data thanks volvo95128.rar

hello after write file control module faulty check light , heater light all but car not start thanks

thanks for reply i reparied dead unit but mcu also short now ecu ok info but need frimware thanks

hello i need skoda laura 2011 ecu file need edc17c46 0281016826 1037519387 03l906018ej diesel , manual gear box thanks

hello i have renault captur 2018 with HFM with card key need ecu coding so i try with renolink pin red of BCM T4 with spc5605 but in with hfm module ecu learn error " no data " if i try with menu uch t4 than error " epprom need to unlock enable it frist " so if any one help me for how to unlock eeprom or how to below attach picture

hello my 4 duster ph2 patrol done thanks to all fo you but now 2 captur with HFM module with jonshon control spc5605 mcu but if i try with renolink , when pin red no data message & if i try with UCH T4 than erpprom need to unlock please unable it , is any one help me thanks topic closed

hello my job done with below trick but still need some help i have one working car so with magic x17 connect via OBD , password read & save , than read map & save so after that read/ write map options highlight after that change new blank ecu & write above map 2560km check light came on than in renolink options KEY/RENULT UCH4 ECU LEARN / all success car start but after ignition on / off not start so agian do ecu learn & with xml file options / after sales ecu paring with 16 dighit pin than do vin write than with launch online confugration data transfer send ok than car start perfect but all do with my working car BCM / KEY so my another set need to BCM VERGIN & code but in this process i not success & i try but ECU CODING SUCCESS thanks all of u for help

hello i have one car with 0 error & this car ecu i made immo off with magic read password obd i have 5 car with ecu lost one member help me & told me for buy combiloader i try but russai paypal not accept so difficuilt to buy , i still try ........... i have 5 new ecu but may this ecu have no data blank bcoz today i just information with renolink scan below attach picture of screen shot renolink thanks