Перейти к содержанию

Master101

Начинающий
  • Постов

    17
  • Зарегистрирован

  • Посещение

Весь контент Master101

  1. Master101

    Vediamo

    Я уже активировал спасибо
  2. Master101

    Vediamo

    Здравствуйте может кто-нибудь активировать ведиаму или отправить файл активации? Спасибо
  3. Спасибo RRoman and j4chip я протестирую и Пишу результат
  4. спасибо за вашу помощь как я могу исправить ошибки Я пробовал ту же ошибку с этим драйвером D-PDU_API V1.20.20 FW 2.20.20 теперь я понимаю, извините, я из Болгарии, я не очень хорошо понимаю, поэтому я еще не пробовал, спасибо
  5. У меня есть ошибки в настройке pssthru, кто может мне помочь? Заранее спасибо D-PDU_API V1.20.23 FW 2.20.23 у кого-нибудь есть этот драйвер для тестирования?
  6. Hello Andrey1842, You make a program and post it here in the forum for people to activate it? Then choose people with whom you think the activation is correct? Then don't promise because of activation people are not a toy!!!
  7. Steering Angle Sensor Internal Circuit DESCRIPTION Steering angle sensor signals are sent to the skid control ECU via the CAN communication system. When there is a malfunction in the CAN communication system, it will be detected by the steering angle sensor zero point malfunction diagnostic function. DTC Code DTC Detection Condition Trouble Area C1433 Either of the following is detected: With the IG1 terminal voltage 9.5 to 17.4 V, the skid control ECU receives an error signal from the steering angle sensor for 0.012 seconds. An open in the sensor power supply circuit for 1 second or more. Spiral cable (Steering angle sensor) WIRING DIAGRAM Refer to DTC C1432 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: C1432: Steering Angle Sensor Power Source Voltage Malfunction (2010 RX350 from 08/2009)+. INSPECTION PROCEDURE HINT: When DTC U0073, U0123, U0124 and/or U0126 is output together with DTC C1433, inspect and repair the trouble areas indicated by DTC U0073, U0123, U0124 and/or U0126 first BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: U0073,U0100,U0123,U0124,U0126: Control Module Communication Bus OFF (2010 RX350 from 08/2009). When any of the speed sensors or the yaw rate and acceleration sensor has trouble, DTCs for the steering angle sensor may be output even when the steering angle sensor is normal. When DTCs for the speed sensors or yaw rate and acceleration sensor are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor first, and then inspect and repair the steering angle sensor. PROCEDURE 1. REPLACE SPIRAL CABLE (STEERING ANGLE SENSOR) (a) Replace the spiral cable (steering angle sensor) BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: STEERING ANGLE SENSOR: REMOVAL (2010 RX350 from 08/2009) . HINT: If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: PROBLEM SYMPTOMS TABLE (2010 RX350 from 08/2009) . NEXT
  8. Больше не знаю здесь, функциональная картинка Просмотрите «возможные причины», перечисленные выше. Визуально осмотрите соответствующий жгут проводов и разъемы. Ищите поврежденные компоненты и ищите сломанные, погнутые, выдвинутые или корродированные контакты разъема. Сигналы датчика угла поворота рулевого колеса отправляются в электронный блок управления системы противоскольжения (ECU) через систему связи Control Area Network (CAN). Когда есть неисправность в системе связи CAN, она будет обнаружена функцией диагностики неисправности нулевой точки датчика угла поворота рулевого колеса. ЭБУ системы противоскольжения контролирует работу датчика угла поворота рулевого колеса. ЭБУ системы противоскольжения устанавливает код OBDII, когда датчик угла поворота рулевого колеса не соответствует заводским спецификациям.
  9. C1433 - Steering Angle Sensor Internal Circuit Problem
×
×
  • Создать...