abbate22

Hi all users, I hope to make myself understood, I use the google translator. I need your precious help on a map, I have fap problems with my car fiat punto evo 1.3mjt 75cv, given that I have eliminated the filter and disabled the egr and fap from the ecu and I would need to check the values with the possibility of increasing about 30 hp to my car. The ECU SW: 9744G102 HW: MJ8DFHW00P MJD 8F2.G1 MARELLI: 51904060, which I am attaching the map already excluding EGR and FAP. Thanks Привет всем пользователям, надеюсь поясняюсь, пользуюсь переводчиком гугл. Мне нужна ваша драгоценная помощь на карте, у меня проблемы с fap с моим автомобилем fiat punto evo 1.3mjt 75cv, учитывая, что я удалил фильтр и отключил egr и fap из ЭБУ, и мне нужно будет проверить значения с помощью возможность увеличения моей машины примерно на 30 л.с. Программное обеспечение ЭБУ: 9744G102 HW: MJ8DFHW00P MJD 8F2.G1 MARELLI: 51904060, карту которого я прилагаю, уже не включая EGR и FAP. Спасибо MARELLI EVO 1.3 MJT 8f2_DPF_EGR_off

nessuno mi aiuta?

Salve, ho provveduto a leggere la mappa della ECU Marelli 8F2 con MPPS v18, avrei bisogno di rimuovere il DPF e EGR più checksum per procedere alla scrittura, allego la mappa originale. grazie PUNTO EVO 1.3 MJT ORI_8f2

Buonasera a tutti, cerco map originale Punto EVO 1.3 MJT 75cv SW: 9744G102 HW: MJ8DFHW00P MJD 8F2.G1 MARELLI: 51904060 GRAZIE

Thanks for the reply. I am not a specialist in the field but I did something in the field of programming. Looking at various links I saw that the MPPS v.18 is used to read and write the eprom of the ECU Marelli 8F2, would it be possible to have a suggestion to start the DPF and EGR removal procedure? thank you

There is no one to help me ????

Hi, I need to remove the DPF and EGR function from my Fiat Punto (8f2), kindly I need help, I bought the MPPS v.18 and v.21 main tricore multiboot, it still hasn't arrived home. From what I could understand I should apply the pins on the ECU, start the MPPS software, connect and save the eprom file on the PC, then with ADS DPF remover I have to exclude the functions and save the file, then reprogram the ECU. I would need the detailed guide ie the connection of the pins to the ECU, the ADS DPF remover software and the detailed guide of using the MPPS. Thank you

HELLO TO EVERYONE I ASK FOR HELP, I AM A BEGINNER, ENTHUSIAST OF ELECTRONICS AND PROGRAMMING, MY CAR DURING REGENERATION (150-200kM) EMITS A LOT OF WHITE COLOR SMOKE. THE CAR HAS TOTAL KM 222.000, I KNOW THAT BECAUSE OF THE VERY FREQUENT REGENERATION, IT CONSUMES A LOT OF ENGINE OIL. 1. Fiat Punto EVO year 12.2011 2. Marelli diesel 1.3 (51904061) 3.MJ8DFHW00P 4. 9744G102 (0002) - (8F2.G1) 5. FAP AND MORE FOR IMPROVEMENT 6. firmware I DO NOT KNOW THE PROCEDURE. I have a Delphi DS-150E interface. I ASK FOR HELP. THANK YOU

Hello! thanks for the reply, for the firmware I transmit the information described through the posted link.

Save to the whole forum, my point evi 1.3mjt 55CV Km 221.000, during the regeneration it emits a streak of white smoke and consequently I noticed an excessive consumption of engine oil, I would like with your help to eliminate the function of the FAP which is definitely the cause of oil consumption. Thank you

Thanks for the reply. The parts look good, I add the photos of the diagnosis and the original eprom file. Eprom 95320 airbag originale.bin

Hello everyone, I come back to the subject for help to restore the airbag red light of the Punto Evo. A few months ago the airbag control unit stopped working and I bought a used ECU with the same codes, I proceeded to recover the eprom file 95320 with the UPA programmer, I reprogrammed the eprom, I connected the control unit in the Punto, it worked for about two hours and only the red light that indicates the failure of the Airbag unit reappears, only aibag passenger and belts remain working, I connect with Multiecuscan and gives me error B0100 - B0109 - B0108 and B1052, all the configuration parameters seem OK in the sense that the resistances are from 2.5 to 3.0 ohms. I note that the old control unit stopped working suddenly without an accident. How can I solve the problem? Thanks for your help

Timele, thanks for the reply. I have multiecuscan, the software appears proxy alignment procedure not required. How can I solve? thank you

Andre4864, thanks for the reply. The original airbag ECU was faulty, when all the lights were on, I took the original 95320 firmware with UPA programmer, I did the scansion and the lights off after one day a red light appears. I make a diagnosis with the errors described. Can I do something from me with decimals eprom? thank you How can I trace the block? firmware to correct? How can I trace the block? firmware to correct?

Help --- I changed the ecu airbag, I loaded the original firmware, it worked one day and only turned on red light. errors b0100 - internal control unit error, red light on. Seat belts and passenger airbags operated unlit. b1052 - airbag node FIS inertial switch control. b10aa - PROXY configuration check.